![]() ![]() If it's clogged, you may simply need to rinse it to solve your problem. Next, inspect the filter inside the water inlet valve. ![]() The hoses should be your first stop: check for kinks, blockages, or holes (which would also result in a leak), and make sure the faucets at the water supply are turned on. If your washer doesn't fill with water in the first phase of a wash cycle, there are only a few components that could be to blame. WHY IS THERE NO WATER GOING INTO MY WASHING MACHINE? A problem with the controls, meanwhile, will definitely demand some expert attention.ĥ. In machines that have belt drives, a loose, worn, or broken belt will prevent the drum from spinning and need to be repaired or replaced. If your washing machine fills and agitates (washes) but doesn't spin, the problem could also be with the lid switch, which tells the washer the lid is closed but may become dislodged by the vibrations of the spin cycle. The washer will shut itself down to prevent any further damage. This is because heavy or bulky loads may unbalance the drum and eventually cause a jam. The most obvious solution to a non-spinning washer is to redistribute the load inside the drum. These items can get caught in many places, including the drain, causing serious draining difficulties. Use a plumber's snake to clear the blockage, and remember to carefully inspect your clothing for small items (coins, tissues, etc.) before you load your washing machine. Drain: It could be that the drain itself-not the washer-is preventing drainage.You may be able to clear any blockages by taking it outside and blasting it with a spray from your garden hose. Turn off the power to the washer, disconnect the hose (have a bucket ready to catch the water), and inspect it for obstructions. Drain hose: Your drain hose could have a kink or blockage that prevents drainage.Make sure moving parts can move freely and are not broken or missing. To reach and inspect the pump, remove the panel (either the front or back depending on your model), detach it, and remove the screen for a thorough rinsing. If it gets blocked, draining will be prevented. Pump: The pump actively removes water from your machine at the end of a cycle.You can either replace the switch yourself or have a qualified technician do it. Press this switch down with your finger and listen for a click or see if the 'lid closed' light turns on (depending on your model). #Ge washing machine top load fullIf this switch malfunctions, you may be left with a drum full of water. Lid switch: The lid switch confirms that the lid is closed, allowing top-load washers to proceed with various stages of the cycle: fill, wash, drain, spin.WHY WON’T MY WASHING MACHINE DRAIN?Ī few different factors could be at work if your washing machine fails to drain at the end of a wash cycle: For front-load washing machines, a front leak could be caused by a damaged or dirty door seal, but a bottom leak is more likely to be caused by a worn drum seal. For top-load washers, a leak from the top could be due to oversudsing or overloading (both of which are easily resolved), whereas a leak from the bottom could suggest an issue with the water pump. The location of the leak can also give you a hint. If you suspect your leak is coming from the back of the washer, move it away from the wall a few inches and hand-tighten all hose connections between the appliance and the supply pipes. Loose hose connections are the most common cause of washer leaks. #Ge washing machine top load professionalIn that case, it may be time to call in a professional to take a look. If you can detect a sewage-like odor (rather than musty or eggy), the issue may be with the standpipe rather than the washer itself. For the drum itself, try running a hot wash cycle with baking soda and white vinegar as described in our full article on washing machine smells. Pay close attention to seals, gaskets, dispensers (which can usually be removed for cleaning) and any other components that come into contact with laundry or detergent. There are plenty of potential causes of washing machine odors, and most of them can be tackled with a thorough clean. ![]() Mold, mildew, soap scum, bacteria, limescale. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |